TamiyaUSA.com - 1/16 R/C M4 Sherman Upgrade to 4 Channels

Tamiya MINI 4D EDUCATIONAL

Home>
1/16 R/C M4 Sherman Upgrade to 4 Channels

4-Channel Operation

Controlling the tank - Illustrations depict controller set to forward movement (left stick is pushed to full throttle)

	Firing the main cannon Firing the cannon creates flashes of light and causes the tank to vibrate. In pursuit of realism, firing interval has been set to 5 seconds (12 blasts a minute for mid-sized tank mode). (Tank does not fire ammunition).
	Method of operation Push the trim lever located on the left side of the right stick to the full-forward position. Rapidly push the right stick from mid-position to full-forward position.
	Gun-turret rotation Realistic sound emitted when turret rotates. Enjoy the thrill of locking your sites on target! Gun-turret speed can be adjusted (Max. speed- 1 rotation per 18sec.).
	Method of operation Move stick left/right to engage left/right turret movement.
	Cannon Elevation Realistic sound emitted when cannon raises/lowers. (Elevates to positive 15 degrees. Lowers to negative 5 degrees).
	Method of operation Move right stick up/down to elevate/lower cannon.
	Firing forward mounted machine gun The forward mounted M1919A4 machine gun emits noise and flashes of light via diode. Machine gun can be fired in 3-second bursts.
	Method of operation Push the trim lever located on the left side of the right stick to the full-down position. Rapidly move the right stick from mid-position to full-down position.
	Engaging lights (front and rear) Now you can enact night missions with even more realism.
	Method of operation Push the trim lever located under the left stick all the way to the right side. Move the left stick rapidly to the upper right. Use the same method to disengage lights.

Wiring the 4-channel receiver

The change from 2-channels to 4-channels is made possible by adding two more wires from the DMD Control Unit T-05 to the receiver. This re-wiring will enable the receiver to pick up 4 signals. The DMD Control Unit T-05 will automatically differentiate signals when turned on.

Attaching DMD Control Unit T-05 to 4-channel receiver

RUDD.- CH1 THROT.- CH2 M.GUN- CH3 TURR.- CH4
*To avoid misconnecting wires from the DMD Control Unit T-05 please affix marker stickers included in kit.

CAUTION:

*Please disconnect extension unit (it will not be used)
*Do not connect receiver battery to power source as this may lead to DMD Control Unit T-05 malfunction.

Please refer to picture when attaching wires. Bind wires with nylon cord to avoid tangling.

Receiver converted from 2-channel to 4-channel use.
Internal wiring can be affixed to under side of upper hull using Aluminum Reinforced Tape (Option Parts, Product No, 53351).
If light valve unit is cut or broken, all 4 lamps must be replaced. Please take care when installing.

Programming the DMD Control Unit T-05

It is always necessary to program the DMD Control Unit T-05. Turn the transmitter switch on and set all trim levers to neutral-position. Program in the following order:

	1) Reset DMD Control Unit T-05 When turning on switch, green light will flash on and off. Push set button with driver included in kit. Hold button down and the drive indicator light will flash alternately from red to orange to green.
	2) Set Left Control Stick (up/down) Move left control stick from the neutral position to the full up and then to the full down position. Drive indicator light will continue to flash red-orange-green.
	3) Set Right Control Stick (left/right) Move right control stick from the neutral position to the full right and then to the full left position. Drive indicator light will continue to flash red-orange-green.
	4) Set Right Control Stick (up/down) Move left control stick from the neutral position to the full up and then to the full down position. Drive indicator light will continue to flash red-orange-green.
	5) Set Left Control Stick (left/right) Move left control sick from the neutral position to the full right and then to the full left position. After completing steps 2-5, L and R indicator lights will alternately flash green and programming will be complete. At this point the computer will have finished recording the control sticks' range of movement.
	6) Final Step Push the set button one more time with the driver included in the kit. Both indicator lights will flash green simultaneously.